Asus DSL-AC52U

Pytania i informacje dotyczące usługi Neostrada TP i Multipakiet TP (VOIP, Video on demand, etc)

Topic author
Rucia1
Użytkownik
Użytkownik
Posty: 13
Rejestracja: 24 sie 2017, 14:34
Numer GG: 0

Re: Asus DSL-AC52U

Nieprzeczytany post autor: Rucia1 » 26 sie 2017, 14:02

Oprogramowanie wgrałam od razu po uruchomieniu routera, także jest najnowsze. Chyba go odeśle do serwisu niech zobaczą.

Awatar użytkownika

best-boy
Administrator
Administrator
Posty: 5025
Rejestracja: 22 maja 2010, 20:21
Łącze: Neostrada
Numer GG: 0
Lokalizacja: LUBANJLG/PE3

Re: Asus DSL-AC52U

Nieprzeczytany post autor: best-boy » 26 sie 2017, 19:57

Rucia1 pisze:Oprogramowanie wgrałam od razu po uruchomieniu routera, także jest najnowsze. Chyba go odeśle do serwisu niech zobaczą.


Próbowałeś go sprzętowo (przyciskiem) resetować po wgraniu nowego softu?
http://www.speedtest.net/my-result/3432356442
Oddam w dobre ręce skrypty do routerów z softem BILION i jego wszystkie klony.


Topic author
Rucia1
Użytkownik
Użytkownik
Posty: 13
Rejestracja: 24 sie 2017, 14:34
Numer GG: 0

Re: Asus DSL-AC52U

Nieprzeczytany post autor: Rucia1 » 27 sie 2017, 11:11

twardy reset był robiony

Awatar użytkownika

best-boy
Administrator
Administrator
Posty: 5025
Rejestracja: 22 maja 2010, 20:21
Łącze: Neostrada
Numer GG: 0
Lokalizacja: LUBANJLG/PE3

Re: Asus DSL-AC52U

Nieprzeczytany post autor: best-boy » 27 sie 2017, 11:42

To nie był by pierwszy taki przypadek.
Wrzuć jakieś screeny ze statusu/logi z routera.
https://fotolister.pl/
Jak masz ustawiony typ WAN ? ADSL WAN (ATM) ?
Próbowałeś wymusić wyższy SNR 8-10 ?
http://www.speedtest.net/my-result/3432356442
Oddam w dobre ręce skrypty do routerów z softem BILION i jego wszystkie klony.


Topic author
Rucia1
Użytkownik
Użytkownik
Posty: 13
Rejestracja: 24 sie 2017, 14:34
Numer GG: 0

Re: Asus DSL-AC52U

Nieprzeczytany post autor: Rucia1 » 02 wrz 2017, 15:44

2011-01-01 00:01:00 [Informational] syslogd started: BusyBox v1.00 (2017.07.27-14:24+0000)
2011-01-01 00:01:01 [Informational] kernel: RTS debug message OFF!
2011-01-01 00:01:01 [Informational] kernel: largeD flag=2 (0:maxD=64, 1:maxD=128, 2:maxD=511)
2011-01-01 00:01:01 [Informational] WAN Connection: Wan link down.
2011-01-01 00:01:01 [Informational] stop_nat_rules: apply the redirect_rules!
2011-01-01 00:01:03 [Debug] kernel: tcapi used greatest stack depth: 10724 bytes left
2011-01-01 00:01:04 [Informational] kernel: Firmware version=[1.1.2.3]
2011-01-01 00:01:06 [Informational] kernel: usbcore: registered new interface driver usbfs
2011-01-01 00:01:06 [Informational] kernel: usbcore: registered new interface driver hub
2011-01-01 00:01:06 [Informational] kernel: usbcore: registered new device driver usb
2011-01-01 00:01:06 [Notice] kernel: SCSI subsystem initialized
2011-01-01 00:01:07 [Informational] kernel: Initializing USB Mass Storage driver...
2011-01-01 00:01:07 [Informational] kernel: usbcore: registered new interface driver usb-storage
2011-01-01 00:01:07 [Informational] kernel: USB Mass Storage support registered.
2011-01-01 00:01:07 [Notice] kernel: ufsd:: trace mask set to 0000000f
2011-01-01 00:01:07 [Notice] kernel: ufsd: driver (lke_9.2.0 lke_9.2.0_r248012_b3, build_host("fsd-bs-cluster01"), acl, ioctl, bdi, sd2(0), wb, bz, tr) loaded at c2703000
2011-01-01 00:01:07 [Notice] kernel: NTFS support included
2011-01-01 00:01:07 [Notice] kernel: Big endian platform
2011-01-01 00:01:07 [Notice] kernel: optimized: speed
2011-01-01 00:01:07 [Notice] kernel: Build_for__ASUS_PRODUCTS_010_k2.6.36_2015-04-30_lke_9.2.0_r248012_b3
2011-01-01 00:01:07 [Notice] kernel:
2011-01-01 00:01:08 [Informational] kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
2011-01-01 00:01:08 [Informational] kernel: rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
2011-01-01 00:01:08 [Informational] kernel: rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
2011-01-01 00:01:08 [Informational] kernel: rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x1fbb0000
2011-01-01 00:01:08 [Informational] kernel: rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
2011-01-01 00:01:08 [Informational] kernel: hub 1-0:1.0: USB hub found
2011-01-01 00:01:08 [Informational] kernel: hub 1-0:1.0: 2 ports detected
2011-01-01 00:01:08 [Informational] kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
2011-01-01 00:01:08 [Informational] kernel: rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
2011-01-01 00:01:08 [Informational] kernel: rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
2011-01-01 00:01:08 [Informational] kernel: rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x1fba0000
2011-01-01 00:01:08 [Informational] kernel: hub 2-0:1.0: USB hub found
2011-01-01 00:01:08 [Informational] kernel: hub 2-0:1.0: 2 ports detected
2011-01-01 00:01:08 [Informational] kernel: usbcore: registered new interface driver usblp
2011-01-01 00:01:09 [Informational] kernel: usbcore: registered new interface driver asix
2011-01-01 00:01:09 [Informational] kernel: usbcore: registered new interface driver cdc_ether
2011-01-01 00:01:09 [Informational] kernel: usbcore: registered new interface driver rndis_host
2011-01-01 00:01:10 [Informational] kernel: cdc_ncm: 14-Mar-2012
2011-01-01 00:01:10 [Informational] kernel: usbcore: registered new interface driver cdc_ncm
2011-01-01 00:01:10 [Informational] kernel: usbcore: registered new interface driver cdc_wdm
2011-01-01 00:01:10 [Informational] kernel: usbcore: registered new interface driver qmi_wwan
2011-01-01 00:01:11 [Informational] kernel: cdc_mbim: loaded
2011-01-01 00:01:11 [Informational] kernel: usbcore: registered new interface driver cdc_mbim
2011-01-01 00:01:11 [Notice] crond[2407]: crond 2.3.2 dillon, started, log level 8
2011-01-01 00:01:11 [Informational] rstats[2413]: [start rstats]
2011-01-01 00:01:14 [Informational] kernel:
2011-01-01 00:01:14 [Informational] kernel: $s: go into unregister_mulif_device
2011-01-01 00:01:14 [Informational] kernel:
2011-01-01 00:01:14 [Informational] kernel: nas8_0: vifname = unregister_mulif_device
2011-01-01 00:01:14 [Informational] kernel: vdev is NULL
2011-01-01 00:01:15 [Informational] kernel: Link State: DSL link up.
2011-01-01 00:01:25 [Informational] kernel: Link State: DSL link down.
2011-01-01 00:01:25 [Informational] kernel: Probe Service Type: PPPoE
2011-01-01 00:01:25 [Informational] kernel:
2011-01-01 00:01:25 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:01:25 [Informational] kernel: sys autopvc set vcpool 0 0 32
2011-01-01 00:01:25 [Informational] kernel: sys autopvc set vcpool 1 0 33
2011-01-01 00:01:25 [Informational] kernel: sys autopvc set vcpool 2 0 34
2011-01-01 00:01:25 [Informational] kernel: sys autopvc set vcpool 3 0 35
2011-01-01 00:01:25 [Informational] kernel: sys autopvc set vcpool 4 0 38
2011-01-01 00:01:25 [Informational] kernel: sys autopvc set vcpool 5 0 40
2011-01-01 00:01:25 [Informational] kernel: sys autopvc set vcpool 6 0 50
2011-01-01 00:01:26 [Informational] kernel: sys autopvc set vcpool 7 0 59
2011-01-01 00:01:26 [Informational] kernel: sys autopvc set vcpool 8 0 66
2011-01-01 00:01:26 [Informational] kernel: sys autopvc set vcpool 9 0 67
2011-01-01 00:01:26 [Informational] kernel: sys autopvc set vcpool 10 0 100
2011-01-01 00:01:26 [Informational] kernel: sys autopvc set vcpool 11 1 32
2011-01-01 00:01:26 [Informational] kernel: sys autopvc set vcpool 12 1 33
2011-01-01 00:01:26 [Informational] kernel: sys autopvc set vcpool 13 1 34
2011-01-01 00:01:26 [Informational] kernel: sys autopvc set vcpool 14 1 35
2011-01-01 00:01:26 [Informational] kernel: sys autopvc set vcpool 15 1 50
2011-01-01 00:01:26 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:01:29 [Informational] kernel: Probe Service Type: PPPoE
2011-01-01 00:01:29 [Informational] kernel:
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 0 1 100
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 1 1 500
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 2 2 32
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 3 6 35
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 4 8 32
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 5 8 35
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 6 8 36
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 7 8 42
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 8 8 48
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 9 8 60
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 10 8 81
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 11 9 148
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 12 10 40
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 13 17 32
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 14 35 33
2011-01-01 00:01:29 [Informational] kernel: sys autopvc set vcpool 15 38 100
2011-01-01 00:01:30 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:01:33 [Informational] kernel: Probe Service Type: PPPoE
2011-01-01 00:01:33 [Informational] kernel:
2011-01-01 00:01:33 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:01:33 [Informational] kernel: sys autopvc set vcpool 0 130 32
2011-01-01 00:01:33 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:02:17 [Informational] kernel: Link State: DSL link up.
2011-01-01 00:02:22 [Informational] kernel: Probe Service Type: PPPoE
2011-01-01 00:02:23 [Informational] kernel:
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set vcpool 0 0 32
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set vcpool 1 0 33
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set vcpool 2 0 34
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set vcpool 3 0 35
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set vcpool 4 0 38
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set vcpool 5 0 40
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set vcpool 6 0 50
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set vcpool 7 0 59
2011-01-01 00:02:23 [Informational] kernel: sys autopvc set vcpool 8 0 66
2011-01-01 00:02:26 [Informational] kernel: Probe Service Type: PPPoE
2011-01-01 00:02:26 [Informational] kernel:
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 0 1 100
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 1 1 500
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 2 2 32
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 3 6 35
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 4 8 32
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 5 8 35
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 6 8 36
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 7 8 42
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 8 8 48
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 9 8 60
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 10 8 81
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 11 9 148
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 12 10 40
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 13 17 32
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 14 35 33
2011-01-01 00:02:26 [Informational] kernel: sys autopvc set vcpool 15 38 100
2011-01-01 00:02:26 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:02:29 [Informational] kernel: log cicmd 7 (wan vdsl2 set sra on )
2011-01-01 00:02:30 [Informational] kernel: US bitswap on,DS bitswap on
2011-01-01 00:02:30 [Informational] kernel: log cicmd 8 (wan vdsl2 set bs_tx on )
2011-01-01 00:02:30 [Informational] kernel: log cicmd 9 (wan vdsl2 set bs on )
2011-01-01 00:02:30 [Informational] kernel: G.VECTOR on
2011-01-01 00:02:30 [Informational] kernel: gvt_ns_flag off
2011-01-01 00:02:30 [Informational] kernel: Set SNRM OFFSET = 2.0 db
2011-01-01 00:02:30 [Informational] kernel: Set Agc Vref1 = 65535 ; Vref2 = 65535 ; Vref3 = 65535
2011-01-01 00:02:30 [Informational] kernel: log cicmd 10 (wan vdsl2 set target_snrm 32767 )
2011-01-01 00:02:30 [Informational] kernel: PROFILE30A_MULTI_MODE
2011-01-01 00:02:30 [Informational] kernel: log cicmd 11 (wan vdsl set agc 65535 65535 65535 65535 )
2011-01-01 00:02:30 [Informational] kernel: log cicmd 12 (wan vdsl set upbo 255 )
2011-01-01 00:02:30 [Informational] kernel: Link State: DSL link down.
2011-01-01 00:02:30 [Informational] kernel: Probe Service Type: PPPoE
2011-01-01 00:02:30 [Informational] kernel:
2011-01-01 00:02:30 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:02:30 [Informational] kernel: sys autopvc set vcpool 0 130 32
2011-01-01 00:02:30 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:02:54 [Informational] WEB: Configuration changed: SysInfo_Entry
2011-01-01 00:03:04 [Informational] WEB: Configuration changed: Account_Entry0
2011-01-01 00:03:04 [Informational] Samba Server: smb daemon is stoped
2011-01-01 00:03:04 [Informational] FTP Server: daemon is stoped
2011-01-01 00:03:05 [Informational] WEB: Configuration changed: SysInfo_Entry
2011-01-01 00:03:05 [Informational] kernel:
2011-01-01 00:03:06 [Informational] kernel:
2011-01-01 00:03:06 [Informational] kernel: wlan_write---goto fopen!!WPSActiveStatus = NULL
2011-01-01 00:03:06 [Informational] kernel: WPSOOBActive = NULL
2011-01-01 00:03:06 [Informational] kernel: ReCounterActive = NULL
2011-01-01 00:03:06 [Informational] kernel: WPSGenPinCode = NULL
2011-01-01 00:03:06 [Informational] kernel: write_wlan_AutoChannelSkipList -(0x20)
2011-01-01 00:03:06 [Informational] kernel: write_wlan_AutoChannelSkipList - (DE)(0xa)
2011-01-01 00:03:06 [Informational] kernel:
2011-01-01 00:03:06 [Informational] kernel: MTPciPollTxRxEmpty
2011-01-01 00:03:06 [Informational] kernel: tx_kickout_fail_count = 0
2011-01-01 00:03:06 [Informational] kernel: tx_timeout_fail_count = 0
2011-01-01 00:03:06 [Informational] kernel: rx_receive_fail_count = 0
2011-01-01 00:03:06 [Informational] kernel: alloc_cmd_msg = 130
2011-01-01 00:03:06 [Informational] kernel: free_cmd_msg = 130
2011-01-01 00:03:06 [Informational] kernel: AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
2011-01-01 00:03:06 [Informational] kernel: RTMPSetPiggyBack(814): Not support for HIF_MT yet!
2011-01-01 00:03:07 [Informational] kernel: RT28xxPciAsicRadioOff(): Not support for HIF_MT yet!
2011-01-01 00:03:07 [Informational] kernel: br0: port 1(ra0) entering forwarding state
2011-01-01 00:03:07 [Informational] kernel: device ra0 left promiscuous mode
2011-01-01 00:03:07 [Informational] kernel: br0: port 1(ra0) entering disabled state
2011-01-01 00:03:07 [Informational] kernel: @@@ ed_monitor_exit : ===>
2011-01-01 00:03:07 [Informational] kernel: @@@ ed_monitor_exit : <===
2011-01-01 00:03:07 [Informational] kernel: andes_pci_erasefw
2011-01-01 00:03:07 [Informational] kernel: ==>rlt_wlan_chip_onoff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0x20b, Reg-WlanFunCtrl=0x20b
2011-01-01 00:03:07 [Informational] kernel: br0: port 6(rai0) entering forwarding state
2011-01-01 00:03:07 [Informational] kernel: device rai0 left promiscuous mode
2011-01-01 00:03:07 [Informational] kernel: br0: port 6(rai0) entering disabled state
2011-01-01 00:03:28 [Informational] kernel: TX_BCN DESC a6ab8000 size = 320
2011-01-01 00:03:28 [Informational] kernel: RX[0] DESC a6aba000 size = 2048
2011-01-01 00:03:28 [Informational] kernel: RX[1] DESC a6abb000 size = 2048
2011-01-01 00:03:28 [Informational] kernel: cfg_mode=9
2011-01-01 00:03:28 [Informational] kernel: cfg_mode=9
2011-01-01 00:03:28 [Informational] kernel: wmode_band_equal(): Band Equal!
2011-01-01 00:03:28 [Informational] kernel: FW Version:_03alpha
2011-01-01 00:03:28 [Informational] kernel: FW Build Date:20150713092411
2011-01-01 00:03:28 [Informational] kernel: AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
2011-01-01 00:03:28 [Informational] kernel: RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
2011-01-01 00:03:28 [Informational] kernel: efuse_probe: efuse = 10000002
2011-01-01 00:03:29 [Informational] kernel: Link State: DSL link up.
2011-01-01 00:03:30 [Informational] Samba Server: daemon is started
2011-01-01 00:03:32 [Error] smbd[5074]: [2011/01/01 00:03:32, 0] auth/auth_util.c:get_root_nt_token(501)
2011-01-01 00:03:32 [Error] smbd[5074]: get_root_nt_token: getpwnam"root") failed!
2011-01-01 00:03:32 [Error] smbd[5074]: [2011/01/01 00:03:32, 0] auth/auth_util.c:get_root_nt_token(501)
2011-01-01 00:03:32 [Error] smbd[5074]: get_root_nt_token: getpwnam"root") failed!
2011-01-01 00:03:32 [Error] smbd[5074]: [2011/01/01 00:03:32, 0] services/services_db.c:svcctl_init_keys(420)
2011-01-01 00:03:32 [Error] smbd[5074]: svcctl_init_keys: key lookup failed! (WERR_ACCESS_DENIED)
2011-01-01 00:03:34 [Informational] kernel: AP SETKEYS WPA2 MAC=68:63:59:A7:96:50
2011-01-01 00:03:34 [Informational] kernel: Probe Service Type: PPPoE
2011-01-01 00:03:34 [Informational] kernel:
2011-01-01 00:03:34 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:03:34 [Informational] kernel: sys autopvc set vcpool 0 8 35
2011-01-01 00:03:35 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:03:36 [Informational] kernel: AP SETKEYS WPA2 MAC=EC:89:F5:35:72:6C
2011-01-01 00:03:36 [Informational] kernel: log cicmd 14 (wan vdsl2 set sra on )
2011-01-01 00:03:36 [Informational] kernel: US bitswap on,DS bitswap on
2011-01-01 00:03:36 [Informational] kernel: log cicmd 15 (wan vdsl2 set bs_tx on )
2011-01-01 00:03:36 [Informational] kernel: log cicmd 16 (wan vdsl2 set bs on )
2011-01-01 00:03:36 [Informational] kernel: G.VECTOR on
2011-01-01 00:03:36 [Informational] kernel: gvt_ns_flag off
2011-01-01 00:03:36 [Informational] kernel: Set SNRM OFFSET = 4.0 db
2011-01-01 00:03:36 [Informational] kernel: Set Agc Vref1 = 65535 ; Vref2 = 65535 ; Vref3 = 65535
2011-01-01 00:03:36 [Informational] kernel: log cicmd 17 (wan vdsl2 set target_snrm 32767 )
2011-01-01 00:03:36 [Informational] kernel: PROFILE30A_MULTI_MODE
2011-01-01 00:03:36 [Informational] kernel: log cicmd 18 (wan vdsl set agc 65535 65535 65535 65535 )
2011-01-01 00:03:36 [Informational] kernel: log cicmd 19 (wan vdsl set upbo 255 )
2011-01-01 00:03:36 [Informational] kernel: G.inp mode
2011-01-01 00:03:36 [Informational] kernel: ANNEXAIJLM
2011-01-01 00:03:36 [Informational] kernel: annex auto-switch flag = 0
2011-01-01 00:03:37 [Informational] kernel: Rcv Wcid(1) AddBAReq
2011-01-01 00:03:37 [Informational] kernel: Start Seq = 00000000
2011-01-01 00:03:37 [Informational] kernel: Link State: DSL link down.
2011-01-01 00:03:38 [Informational] kernel: AP SETKEYS WPA2 MAC=E0:CA:94:CA:E2:97
2011-01-01 00:03:43 [Informational] kernel: Rcv Wcid(1) AddBAReq
2011-01-01 00:03:43 [Informational] kernel: Start Seq = 00000001
2011-01-01 00:03:44 [Informational] kernel: 23, flush one!
2011-01-01 00:04:31 [Informational] kernel: Link State: DSL link up.
2011-01-01 00:04:36 [Informational] kernel: Probe Service Type: PPPoA
2011-01-01 00:04:36 [Informational] kernel:
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set vcpool 0 0 32
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set vcpool 1 0 35
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set vcpool 2 0 38
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set vcpool 3 0 100
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set vcpool 4 1 33
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set vcpool 5 1 50
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set vcpool 6 8 35
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set vcpool 7 8 48
2011-01-01 00:04:36 [Informational] kernel: sys autopvc set vcpool 8 35 33
2011-01-01 00:04:37 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:04:43 [Informational] kernel: US bitswap on,DS bitswap on
2011-01-01 00:04:43 [Informational] kernel: G.VECTOR on
2011-01-01 00:04:43 [Informational] kernel: gvt_ns_flag off
2011-01-01 00:04:43 [Informational] kernel: Set SNRM OFFSET = 5.0 db
2011-01-01 00:04:43 [Informational] kernel: Set Agc Vref1 = 65535 ; Vref2 = 65535 ; Vref3 = 65535
2011-01-01 00:04:43 [Informational] kernel: PROFILE30A_MULTI_MODE
2011-01-01 00:04:43 [Informational] kernel: G.inp mode
2011-01-01 00:04:43 [Informational] kernel: ANNEXAIJLM
2011-01-01 00:04:43 [Informational] kernel: annex auto-switch flag = 0
2011-01-01 00:04:44 [Informational] kernel: Link State: DSL link down.
2011-01-01 00:04:45 [Informational] kernel: Probe Service Type: PPPoA
2011-01-01 00:04:45 [Informational] kernel:
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 0 0 32
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 1 0 33
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 2 0 35
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 3 0 36
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 4 0 38
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 5 0 50
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 6 0 100
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 7 1 32
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 8 1 33
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 9 1 35
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 10 1 50
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 11 5 35
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 12 8 32
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 13 8 35
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 14 8 48
2011-01-01 00:04:45 [Informational] kernel: sys autopvc set vcpool 15 8 80
2011-01-01 00:04:46 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:04:49 [Informational] kernel: Probe Service Type: PPPoA
2011-01-01 00:04:49 [Informational] kernel:
2011-01-01 00:04:49 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:04:49 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:05:38 [Informational] kernel: Link State: DSL link up.
2011-01-01 00:05:43 [Informational] kernel: Probe Service Type: DHCP
2011-01-01 00:05:44 [Informational] kernel:
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set vcpool 0 0 32
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set vcpool 1 0 33
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set vcpool 2 0 34
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set vcpool 3 0 35
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set vcpool 4 0 37
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set vcpool 5 0 44
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set vcpool 6 0 96
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set vcpool 7 0 100
2011-01-01 00:05:44 [Informational] kernel: sys autopvc set vcpool 8 0 101
2011-01-01 00:05:44 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:05:50 [Informational] kernel: Link State: DSL link down.
2011-01-01 00:05:53 [Informational] kernel: Probe Service Type: DHCP
2011-01-01 00:05:53 [Informational] kernel:
2011-01-01 00:05:53 [Informational] kernel: sys autopvc set mac 70 8b cd b5 ac 20
2011-01-01 00:05:53 [Informational] kernel: sys autopvc set vcpool 0 0 40
2011-01-01 00:05:53 [Informational] kernel: sys autopvc set vcpool 1 8 32
2011-01-01 00:05:53 [Informational] kernel: sys autopvc set vcpool 2 8 35
2011-01-01 00:05:53 [Informational] kernel: sys autopvc probe vcpool
2011-01-01 00:06:07 [Informational] kernel:
2011-01-01 00:06:07 [Informational] kernel: $s: go into unregister_mulif_device
2011-01-01 00:06:07 [Informational] kernel:
2011-01-01 00:06:07 [Informational] kernel: nas8_0: vifname = unregister_mulif_device
2011-01-01 00:06:07 [Informational] kernel: vdev is NULL
2011-01-01 00:06:09 [Informational] RFC1483/2684 bridge: Interface "nas0" created sucessfully
2011-01-01 00:06:13 [Informational] RFC1483/2684 bridge: Communicating over ATM 0.0.35, encapsulation: LLC
2011-01-01 00:06:13 [Informational] kernel: mt7510_config
2011-01-01 00:06:13 [Informational] kernel: mt7510_atm_open
2011-01-01 00:06:13 [Informational] kernel: vpi: 0
2011-01-01 00:06:13 [Informational] kernel: vci: 35
2011-01-01 00:06:13 [Informational] kernel: mt7510_atm_open vc 0:
2011-01-01 00:06:13 [Informational] kernel: ASIC dslUpRate Setting
2011-01-01 00:06:13 [Informational] kernel: ATM over ADSL mode init
2011-01-01 00:06:13 [Informational] kernel: dslUpRate: 2416
2011-01-01 00:06:13 [Informational] kernel: enter br2684_init_hook function
2011-01-01 00:06:13 [Informational] kernel: mt7510_init_MPOA
2011-01-01 00:06:13 [Informational] WEB: Configuration changed: Route
2011-01-01 00:06:13 [Informational] kernel: SRAON
2011-01-01 00:06:13 [Informational] kernel: US bitswap on,DS bitswap on
2011-01-01 00:06:13 [Informational] kernel: OlrON
2011-01-01 00:06:13 [Informational] kernel: G.VECTOR on
2011-01-01 00:06:13 [Informational] kernel: gvt_ns_flag off
2011-01-01 00:06:13 [Informational] kernel: Set SNRM OFFSET = 5.0 db
2011-01-01 00:06:13 [Informational] kernel: Set Agc Vref1 = 65535 ; Vref2 = 65535 ; Vref3 = 65535
2011-01-01 00:06:13 [Informational] kernel: AGC Vref1 = 65535 ; Vref2 = 65535 ; Vref3 = 65535 ; Vref4 = 65535
2011-01-01 00:06:13 [Informational] kernel: Reset sync sym update to default value !!!
2011-01-01 00:06:16 [Informational] kernel: PROFILE30A_MULTI_MODE
2011-01-01 00:06:17 [Informational] kernel: G.inp mode
2011-01-01 00:06:17 [Informational] kernel: ANNEXAIJLM
2011-01-01 00:06:17 [Informational] kernel: annex auto-switch flag = 0
2011-01-01 00:06:17 [Informational] WEB: Configuration changed: Adsl_Entry
2011-01-01 00:06:17 [Informational] WAN Connection: Wan link down.
2011-01-01 00:06:21 [Informational] kernel: AP SETKEYS WPA2 MAC=40:40:A7:5B:99:21
2011-01-01 00:06:21 [Debug] kernel: nas0: no IPv6 routers present
2011-01-01 00:06:23 [Informational] kernel: Rcv Wcid(1) AddBAReq
2011-01-01 00:06:23 [Informational] kernel: Start Seq = 000000b7
2011-01-01 00:06:43 [Informational] kernel: Rcv Wcid(1) AddBAReq
2011-01-01 00:06:43 [Informational] kernel: Start Seq = 000000ba
2011-01-01 00:06:46 [Informational] kernel: Rcv Wcid(1) AddBAReq
2011-01-01 00:06:46 [Informational] kernel: Start Seq = 000000bd
2011-01-01 00:06:47 [Informational] kernel: Rcv Wcid(1) AddBAReq
2011-01-01 00:06:47 [Informational] kernel: Start Seq = 000000be
2011-01-01 00:06:50 [Informational] kernel: Rcv Wcid(1) AddBAReq
2011-01-01 00:06:50 [Informational] kernel: Start Seq = 000000c1
2011-01-01 00:06:50 [Informational] kernel: Rcv Wcid(1) AddBAReq
2011-01-01 00:06:50 [Informational] kernel: Start Seq = 000000c2
2011-01-01 00:07:00 [Informational] kernel: Rcv Wcid(2) AddBAReq
2011-01-01 00:07:00 [Informational] kernel: Start Seq = 00000010
2011-01-01 00:07:02 [Informational] kernel: Rcv Wcid(1) AddBAReq
2011-01-01 00:07:02 [Informational] kernel: Start Seq = 000000c9
2011-01-01 00:07:09 [Informational] kernel: log cicmd 0 (wan dmt2 set olr 3 )
2011-01-01 00:07:09 [Informational] kernel: US bitswap on,DS bitswap on
2011-01-01 00:07:09 [Informational] kernel: log cicmd 1 (wan dmt2 set olr 1 )
2011-01-01 00:07:09 [Informational] kernel: G.VECTOR on
2011-01-01 00:07:09 [Informational] kernel: gvt_ns_flag off
2011-01-01 00:07:09 [Informational] kernel: Set SNRM OFFSET = 5.0 db
2011-01-01 00:07:09 [Informational] kernel: log cicmd 2 (wan dmt2 set snrm -2560 -2560 )
2011-01-01 00:07:09 [Informational] kernel: Set Agc Vref1 = 65535 ; Vref2 = 65535 ; Vref3 = 65535
2011-01-01 00:07:09 [Informational] kernel: log cicmd 3 (wan dmt2 set vref 65535 65535 65535 65535 )
2011-01-01 00:07:09 [Informational] kernel: log cicmd 4 (wan dmt2 set updatesync default )
2011-01-01 00:07:11 [Informational] kernel: PROFILE30A_MULTI_MODE
2011-01-01 00:07:11 [Informational] kernel: G.inp mode
2011-01-01 00:07:11 [Informational] kernel: ANNEXA
2011-01-01 00:07:11 [Informational] kernel: annex auto-switch flag = 0
2011-01-01 00:07:11 [Informational] WEB: Configuration changed: Adsl_Entry
2011-01-01 00:07:22 [Informational] kernel: set cicmd 5
2011-01-01 00:07:22 [Informational] kernel: 1: wan dmt2 set olr 3
2011-01-01 00:07:22 [Informational] kernel: SRAON
2011-01-01 00:07:22 [Informational] kernel: dmt2 set olr 1
2011-01-01 00:07:22 [Informational] kernel: OlrON
2011-01-01 00:07:22 [Informational] kernel:
2011-01-01 00:07:22 [Informational] kernel: 65535 65535 65535
2011-01-01 00:07:22 [Informational] kernel: AGC Vref1 = 65535 ; Vref2 = 65535 ; Vref3 = 65535 ; Vref4 = 65535
2011-01-01 00:07:22 [Informational] kernel: 5: wan dmt2 set updatesync default
2011-01-01 00:07:22 [Informational] kernel: Reset sync sym update to default value !!!
2011-01-01 00:09:21 [Informational] kernel: tc3162_atm_close done
2011-01-01 00:09:21 [Informational] kernel:
2011-01-01 00:09:21 [Informational] kernel: ==> check_mulif_interface_existnas0
2011-01-01 00:09:21 [Informational] kernel: ==> to find mulif group of device nas0
2011-01-01 00:09:21 [Informational] kernel: ==>mulif err, no find mulif group of device nas0
2011-01-01 00:09:22 [Informational] RFC1483/2684 bridge: Interface "nas0" created sucessfully
2011-01-01 00:09:22 [Informational] RFC1483/2684 bridge: Communicating over ATM 0.0.35, encapsulation: VC mux
2011-01-01 00:09:22 [Informational] kernel: mt7510_config
2011-01-01 00:09:22 [Informational] kernel: mt7510_atm_open
2011-01-01 00:09:22 [Informational] kernel: vpi: 0
2011-01-01 00:09:22 [Informational] kernel: vci: 35
2011-01-01 00:09:22 [Informational] kernel: mt7510_atm_open vc 0:
2011-01-01 00:09:22 [Informational] kernel: ASIC dslUpRate Setting
2011-01-01 00:09:22 [Informational] kernel: ATM over ADSL mode init
2011-01-01 00:09:22 [Informational] kernel: dslUpRate: 2416
2011-01-01 00:09:22 [Informational] kernel: enter br2684_init_hook function
2011-01-01 00:09:22 [Informational] kernel: mt7510_init_MPOA
2011-01-01 00:09:22 [Informational] kernel: Init VC 0 MPOA Function
2011-01-01 00:09:22 [Informational] kernel: MPOA Mode: MODE_BRIDGE
2011-01-01 00:09:22 [Informational] kernel: MuxType: MUX_VC
2011-01-01 00:09:22 [Informational] kernel: Mode: MODE_BRIDGE
2011-01-01 00:09:22 [Informational] kernel: br2684_init_hook: success
2011-01-01 00:09:22 [Informational] RFC1483/2684 bridge: Interface configured
2011-01-01 00:09:22 [Informational] RFC1483/2684 bridge: RFC 1483/2684 bridge daemon started
2011-01-01 00:09:23 [Informational] syslog: Initialize LCP.
2011-01-01 00:09:25 [Informational] syslog: Plugin libpppoe.so loaded.
2011-01-01 00:09:25 [Informational] syslog: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
2011-01-01 00:09:25 [Notice] syslog: pppd 2.4.5 started by admin, uid 0
2011-01-01 00:09:25 [Informational] syslog: LCP is allowed to come up.
2011-01-01 00:09:25 [Informational] kernel: generate miniupnpd.conf
2011-01-01 00:09:25 [Informational] kernel: launch upnp
2011-01-01 00:09:25 [Informational] kernel: start_miniupnpd. force(1)
2011-01-01 00:09:25 [Informational] kernel: stop upnp first
2011-01-01 00:09:25 [Informational] kernel: /userfs/bin/miniupnpd -P /var/log/upnpd.pid -f /var/tmp/miniupnpd.conf &
2011-01-01 00:09:25 [Informational] WEB: Configuration changed: Route
2011-01-01 00:09:33 [Debug] kernel: nas0: no IPv6 routers present
2011-01-01 00:11:45 [Informational] kernel: check_log_path: [AccessLog]
2011-01-01 00:12:13 [Debug] kernel: iwpriv used greatest stack depth: 10700 bytes left
2011-01-01 00:12:28 [Notice] kernel: klogd started: BusyBox v1.00 (2017.07.27-14:24+0000)
2011-01-01 00:12:28 [Informational] System log daemon exiting.
2011-01-01 00:12:29 [Informational] syslogd started: BusyBox v1.00 (2017.07.27-14:24+0000)
2011-01-01 01:17:58 [Informational] kernel: tc3162_atm_close done
2011-01-01 01:17:58 [Informational] kernel:
2011-01-01 01:17:58 [Informational] kernel: ==> check_mulif_interface_existnas0
2011-01-01 01:17:58 [Informational] kernel: ==> to find mulif group of device nas0
2011-01-01 01:17:58 [Informational] kernel: ==>mulif err, no find mulif group of device nas0
2011-01-01 01:17:59 [Debug] kernel: hotplug used greatest stack depth: 10692 bytes left
2011-01-01 01:17:59 [Informational] RFC1483/2684 bridge: Interface "nas0" created sucessfully
2011-01-01 01:17:59 [Informational] kernel: mt7510_config
2011-01-01 01:17:59 [Informational] RFC1483/2684 bridge: Communicating over ATM 0.0.35, encapsulation: LLC
2011-01-01 01:17:59 [Informational] kernel: mt7510_atm_open
2011-01-01 01:17:59 [Informational] kernel: vpi: 0
2011-01-01 01:17:59 [Informational] kernel: vci: 35
2011-01-01 01:17:59 [Informational] kernel: mt7510_atm_open vc 0:
2011-01-01 01:17:59 [Informational] kernel: ASIC dslUpRate Setting
2011-01-01 01:17:59 [Informational] kernel: ATM over ADSL mode init
2011-01-01 01:17:59 [Informational] kernel: dslUpRate: 2416
2011-01-01 01:18:00 [Informational] kernel: enter br2684_init_hook function
2011-01-01 01:18:00 [Informational] kernel: mt7510_init_MPOA
2011-01-01 01:18:00 [Informational] kernel: Init VC 0 MPOA Function
2011-01-01 01:18:00 [Informational] kernel: MPOA Mode: MODE_BRIDGE
2011-01-01 01:18:00 [Informational] kernel: MuxType: MUX_LLC
2011-01-01 01:18:00 [Informational] kernel: Mode: MODE_BRIDGE
2011-01-01 01:18:00 [Informational] kernel: br2684_init_hook: success
2011-01-01 01:18:00 [Informational] RFC1483/2684 bridge: Interface configured
2011-01-01 01:18:00 [Informational] RFC1483/2684 bridge: RFC 1483/2684 bridge daemon started
2011-01-01 01:18:01 [Informational] syslog: Initialize LCP.
2011-01-01 01:18:07 [Informational] syslog: Plugin libpppoe.so loaded.
2011-01-01 01:18:07 [Informational] syslog: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
2011-01-01 01:18:07 [Notice] syslog: pppd 2.4.5 started by admin, uid 0
2011-01-01 01:18:07 [Informational] syslog: LCP is allowed to come up.
2011-01-01 01:18:07 [Informational] kernel: generate miniupnpd.conf
2011-01-01 01:18:07 [Informational] kernel: launch upnp
2011-01-01 01:18:07 [Informational] kernel: start_miniupnpd. force(1)
2011-01-01 01:18:07 [Informational] kernel: stop upnp first
2011-01-01 01:18:07 [Informational] kernel: /userfs/bin/miniupnpd -P /var/log/upnpd.pid -f /var/tmp/miniupnpd.conf &
2011-01-01 01:18:07 [Informational] WEB: Configuration changed: Route
2011-01-01 01:18:11 [Debug] kernel: nas0: no IPv6 routers present

Awatar użytkownika

best-boy
Administrator
Administrator
Posty: 5025
Rejestracja: 22 maja 2010, 20:21
Łącze: Neostrada
Numer GG: 0
Lokalizacja: LUBANJLG/PE3

Re: Asus DSL-AC52U

Nieprzeczytany post autor: best-boy » 03 wrz 2017, 10:37

Łączy i rozłącza i tak na okrętkę, w dodatku próbuje wszystkie kombinacje vpi/vci tak jakby szukał odpowiedniej.
Może zamiast przez quick setup ustaw wszystko ręcznie?
http://www.speedtest.net/my-result/3432356442
Oddam w dobre ręce skrypty do routerów z softem BILION i jego wszystkie klony.


Topic author
Rucia1
Użytkownik
Użytkownik
Posty: 13
Rejestracja: 24 sie 2017, 14:34
Numer GG: 0

Re: Asus DSL-AC52U

Nieprzeczytany post autor: Rucia1 » 03 wrz 2017, 11:49

Wszystko ustawiam ręcznie, przy quick setup jest komunikat " nie podłączono kabla telefonicznego " i nie idzie dalej konfiguracja.

Awatar użytkownika

januszvdsl2
Starszy Użytkownik
Starszy Użytkownik
Posty: 205
Rejestracja: 01 gru 2013, 7:33
Łącze: Brak :-)
Numer GG: 0

Re: Asus DSL-AC52U

Nieprzeczytany post autor: januszvdsl2 » 03 wrz 2017, 16:54

Rucia1 pisze:Wszystko ustawiam ręcznie, przy quick setup jest komunikat " nie podłączono kabla telefonicznego " i nie idzie dalej konfiguracja.

@Rucia1 Widzę ze używasz /ipv6 czy się mylę? xxxxxxx@neostrada.pl/ipv6 czy bez tego xxxxxxxxxxx@neostrada.pl ?
Sprzęt : Huawei B525 :grin:
intel dual band wireless-ac 7260


Topic author
Rucia1
Użytkownik
Użytkownik
Posty: 13
Rejestracja: 24 sie 2017, 14:34
Numer GG: 0

Re: Asus DSL-AC52U

Nieprzeczytany post autor: Rucia1 » 03 wrz 2017, 16:59

próbowałam i z ipv6 wpisywać i bez

Awatar użytkownika

best-boy
Administrator
Administrator
Posty: 5025
Rejestracja: 22 maja 2010, 20:21
Łącze: Neostrada
Numer GG: 0
Lokalizacja: LUBANJLG/PE3

Re: Asus DSL-AC52U

Nieprzeczytany post autor: best-boy » 04 wrz 2017, 8:26

Chyba pozostaje reklamacja, tak czy siak dziwnie ten log wygląda.
http://www.speedtest.net/my-result/3432356442
Oddam w dobre ręce skrypty do routerów z softem BILION i jego wszystkie klony.

ODPOWIEDZ Poprzedni tematNastępny temat

Kto jest online

Użytkownicy przeglądający to forum: Obecnie na forum nie ma żadnego zarejestrowanego użytkownika i 11 gości